LM311N DATASHEET PDF

LMN Datasheet, LMN National Semiconductor Voltage Comparator Datasheet, buy LMN. The LM, LM, LM are voltage comparators that have low input currents. They are also designed to operate over a wide range of. Part, LMN. Category. Description, Voltage Comparators. Company, ST Microelectronics, Inc. Datasheet, Download LMN datasheet. Cross ref.

Author: Faushura Dalabar
Country: Costa Rica
Language: English (Spanish)
Genre: Art
Published (Last): 16 September 2012
Pages: 257
PDF File Size: 4.32 Mb
ePub File Size: 13.57 Mb
ISBN: 985-6-34087-582-1
Downloads: 38596
Price: Free* [*Free Regsitration Required]
Uploader: Mauzshura

The problem is that the strobe pin is not working for the model. I tried adding datassheet a transistor with a 1k resistor to ground and a TTL signal at the base as per the datasheet and this doesn’t disable the output either. The simplified schematics of the IC is shown below:.

If the voltage at the Non-Inverting Terminal pin 2 is higher than the Inverting Terminal pin 2the output pin 7 will also be high else the output will be low. You can note that the Output voltage stays high when pin 2 has higher voltage than pin 7 and vice versa. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

LMN Comparator with Strobe. Message 2 of 5. This pin is connected to the ground of the system Negative voltage can also be used.

  AT45DB041D SU PDF

LMN Datasheet(PDF) – National Semiconductor (TI)

The output is correct as seen on the scope. Most Active Software Boards: Any help is appreciated. Message 5 of 5. All of those comparator outputs should be a high state which means the LED will turn on connected through the 1K resistor to Vcc.

As grounding unused pins is a practice on electronics, I guess it was the way of the designer to make sure the device was not disabled for datawheet ground wired to that pin. Message 4 of 5. According to the datasheet, if you tie the strobe pin to GND then the output should be disabled.

Texas Instruments/TI LMN/NOPB – PDF Datasheet – Analog Comparators In Stock |

A sample circuit is shown below in which the Inverting Terminal is set to 2. The LM can work on a Single supply voltage or in a dual supply mode. The pins 5 and 6 on the Op-amp are used to set the balance voltage if you want to manually adjust the DC-Offset voltage.

You can lm311b the other possible circuits from the LM datasheet given at bottom. Normally these pins are not used since the Input Offset itself is much better controlled.

Why is it not working in Multisim? When not in use the pins 5 and 6 should be shorted as shown above.

Multisim and Ultiboard

Message 3 of 5. I just built the circuit in real life and it works exactly as I thought, putting GND on the strobe pin datssheet the output a constant state at Vcci.

  INDUCTION AND SYNCHRONOUS MACHINES BY MURUGESH KUMAR PDF

The transistor can also make the Load to be isolated from the system ground, so if you are looking for a Voltage comparator to drive loads of these specifications then this IC might be the right choice for you. The problem is that tying the strobe pin to ground should make the output stop changing, and it isn’t.

Could the component model be the issue? I built a simple circuit using the LMN comparator. Submitted by admin on 6 March Message 1 of 5. Any Op-Amp can be made to work as a voltage comparator, but the LM proves itself to be advantages by housing an Output Transistor inside its package. Attached is a Multisim file with every comparator with a strobe feature available in Multisim and a picture of the circuit. An Emitter Output Circuit is shown below. I expect the output to oscillate between 0 and 1 at the “zero crossing” of the signal.

The simplified schematics of the IC is shown below: TL — Programmable Reference Voltage.