Icharger B Pdf User Manuals. View online or download Icharger B User Manual. Read online or download PDF • Page 4 / 33 • ProgressiveRC B iCharger User Manual • ProgressiveRC Power suppliers. My iCharger B was one of the earliest released so it has firmware version where as current models are shipping with version

Author: Akikus Faulrajas
Country: Uruguay
Language: English (Spanish)
Genre: Love
Published (Last): 22 March 2007
Pages: 219
PDF File Size: 13.48 Mb
ePub File Size: 14.69 Mb
ISBN: 448-9-55371-829-9
Downloads: 61489
Price: Free* [*Free Regsitration Required]
Uploader: Tera

iCharger 208B Manuals

NiCd and NiMH packs of up to 25 cells and lead-acid of up to 18 cells can be charged in unbalanced mode. My compliments on the graphic design, more eye-catching ixharger the plain blue of the original Chargery units. Error messages If there is a problem during the charge an error message will be displayed. Turnigybut be prepared for some very unusual choices of words.

iCharger B+, B+, B, B, B and B – RC Groups

When you use other equipment to charge or discharge a. Basically you can use any power supply you want as long as its output voltage is icnarger. Mar 28, Should your B need serviced or replaced your first point of contact is the retailer that you purchased the unit from. The correct solution to break this loop is the use of opto-isolators, but icharver B breaks the loop by disconnecting the ground wire of the USB cable.

The charge current is very accurate, even beating out the Watt’s Up meter. DC power input cables and USB connector.

ProgressiveRC 208B iCharger User Manual

I have three of the TP kind and am a big fan of them as they have the bulit in ability to connect balance taps in parallel and serial.

Firmware updates The manual includes a set of directions ichafger updating the firmware on page 29 or page 28 in older versions of the manual.

Pressing “Inc” or “Dec” button will then cause you to move up and down it note the blue text indicating this. If the balancing connector has correct polarity, and then connect the main charging port, there is no problem; but if balancing connector has reversed polarity, and then connect the main charging port, it will burn.


The back of the B circuit board. For me this was my first charger with this kind of menu so I had to refer to the manual a lot and I felt like the information was very disconnected and I would often have to reference 2 or 3 sections of the manual just to figure out how to change a specific setting. Therefore I offer two quick start examples in order to demonstrate a typical usage. Do not charge a battery unattended Do not maanual near flammable objects Do not exceed the rated cell voltage for your ambient temperature typically 4.

One complaint I have is that if you have button beeps turned off you won’t get a beep acknowledging the cancel so you have to go off of the data displayed on the screen to verify that the charger halted the charge. Similarly, LiFe A packs of cells can be charged in balance mode or cells in unbalanced mode.

The charger may say it just charged my icbarger to 3. Over all I rate the manual a “B” as all the information seems to be there and is fairly understandable, but it 2008b has room for improvement. With the exception of the low indication of power and temperature these results are very good.

Connect iCharger’s input power supply, and turn on it.

Icharger B Manuals

Notice that the charger balanced to within 5mV, within its advertised limit. Of course there manuap shipping to consider. The second example assumes the last battery charged is identical and all of the parameters are correct so nothing needs changed. There is table of error messages in the back of the user manual, but as often the case the error displayed on the screen and its description in the manual might mean little to the end user.

  2576T ADJ PDF

The voltage range for cells are all shown and they can be scaled individually or as a group. The front of the B circuit board. Originally Posted by theShark if its W max does it really charge 10S at 10amp?

Images View all Images in thread Views: Having identical scales shown to the left and the right for each of the six cells is a bit annoying as you would probably never want to view them on different scales.

Looks and sounds like. Another reason they caught my eye was their thread on RCGroups where they listen to customer feedback and use the feedback to fix bugs and add features. Connect Li batteries’ balance port 3. See details in Attachment. In the case that the message doesn’t help you find the cause of the problem it is useful for asking others what could cause that message to pop up or 208g determining if repairs need to be made.

As you can see by the picture immediately below, the iCharger B is only slightly larger than the FMA Multi4 yet boasts seven times the power and twice the output cell count. Support upgrading the hardware program ixharger USB port. See detail information about logview in the following website: Files View all Files in thread.

The B has access to several safety features but does not always enforce them, so you’ve got plenty of rope to hang yourself with it if you manuwl choose. The B is advertised to balance cells to within 10mV. Last edited by junsi; Mar 21, at When you use other equipment to charge or discharge a Manuql pack, you can use the iCharger to monitor the per-cell voltages, battery temperature and process time.