BEAGLEBOARD XM SCHEMATICS PDF

BeagleBoard-xM is based on the TI DM and delivers increased performance . The schematic and PCB remain the same as revision C1. BeagleBoard-xM LCD7. System Reference Manual. Revision B. Page 2 of THIS DOCUMENT. This work is licensed under the Creative. BeagleBoard-xM Rev C System Reference Manual Revision April 4, Page 1 of REF: BB_SRM_xM. BeagleBoard-xM System Reference Manual.

Author: Kagall Tonos
Country: Nigeria
Language: English (Spanish)
Genre: Science
Published (Last): 1 April 2013
Pages: 45
PDF File Size: 9.62 Mb
ePub File Size: 4.19 Mb
ISBN: 120-1-93641-115-2
Downloads: 98701
Price: Free* [*Free Regsitration Required]
Uploader: Brajora

Page of Go. Processor Pin Muxing Settings Table 4 is a list of all of the signals used on the processor for beagpeboard BeagleBoard and the required mode setting for each pin. These versions are 2.

BeagleBoard Hardware Design

To print the manual completely, please, download it. Download the HP Formatting tool from one of the following locations. Retrieved from ” schematice Beagleboard Expansion Schhematics Design Information This section provides information on what is required from a mechanical and electrical aspect to create expansion cards for the BeagleBoard that are designed to connect to the Expansion header on the BeagleBoard.

Beagleboard Lcd Header Location 6. Dvi-d Interface These are the loading options to enable the new mode used by the —xM or the legacy mode used by the BeagleBoard.

Figure 16 shows the location schemahics the microSD connector. The supply must have a 2. This pin disables the I2C mode on chip.

After the image writing is done, eject the SD card. Table 4 is a list of all of the signals used on the processor for the BeagleBoard and the required mode setting for each pin. R14 and R15, the actual voltage can be adjusted if needed.

  CATRAX MASTER PDF

BeagleBoard to gain 1GHz SoC, Ethernet

Further, the user indemnifies BeagleBoard. The proper setting of this rail is determined by the application and the HW supplied that connects to P All derivative works are to be attributed to Gerald Coley of BeagleBoard. It is can be used by the UBoot SW to beagleboafd between user scripts to allow different boot configurations to be selected as long as that beagleboad is included in the UBoot used.

JTAG debugging interface 7. Page – Figure 42 is the microSD interface design on the BeagleBoard. All signals from the BeagleBoard are at 1.

Figure 45 is the design of the S- Video interface. The audio cables are not provided with the BeagleBoard-xM, but can be obtained from just about anywhere. beagkeboard

BeagleBoard XM C2 Reference Manual

Figure 1 is a picture of each of these versions. Processor Pin Muxing Settings Turning on this LED is not something that a person should try to do as it indicates that the user is not paying attention and has plugged in a potentially damaging power supply into the power jack. Figure 14 shows the location of each indicator. To download all files at once please click here.

P10 Camera Signals Pin All boards will be returned via standard mail if an issue is found. Reset Circuitry Page 65 – Figure By setting this value in the control register, this signal will be routed to the corresponding pin of the expansion connector.

  CORAZON ESPINADO TAB PDF

This section provides information on what is required from a mechanical and electrical aspect to create expansion cards for the BeagleBoard that are designed to connect to the Expansion header on the BeagleBoard. Follow the instructions found there, but use the images located on this site. There are instances where the PC or laptop does not supply sufficient current to power the board as it does not provide wchematics full mA.

Optional Battery Location Figure Page 15 Covered in this section are a few of the accessories that may be used schemztics BeagleBoard. CAPM The charge pump flying capacitor minus. TPS and what remains from the current consumed by the BeagleBoard and is intended to be used to provide a rail for voltage level conversion only.

You can download the file at Allegro Viewer.

The ULPI used on the BeagleBoard keeps this down to only 12 signals because it combines just three control signals, plus clock, with an 8-bit bi-directional data bus.

The user assumes all responsibility and liability for proper and safe handling of the goods. Page 47 – Figure These are the loading options to enable the new mode used by the —xM or the legacy mode used by the BeagleBoard.